SolarEdge + Nibe

What Zerofy can do with SolarEdge and Nibe

In practice

• Hot water is the simplest heat store: Autopilot can use the hot-water boost of your Nibe heat pump to heat water in hours with surplus.
• A heat pump draws roughly 1–3 kW while running, which a typical SolarEdge home system (3–10 kW) can cover on sunny days.
• Zerofy gets new SolarEdge data every 5 minutes. Heat pumps shouldn’t switch often, so set a minimum runtime in Autopilot.
• Zerofy also shows your SolarEdge battery, so you can see whether surplus goes into the battery or into the heat pump.
• Leave the normal hot-water comfort mode at a moderate level so the tank has headroom; a boost triggered on surplus then stores midday solar as hot water for the evening. EME 20 is not needed for this, since Zerofy reads the surplus from your inverter’s cloud.

What SolarEdge and Nibe offer on their own

SolarEdge: The SolarEdge Home Load Controller switches the SG Ready input of most air-to-water heat pumps on excess solar, with two configurable set points; it connects to the inverter via the SolarEdge Home Network and needs no ONE Controller. Vaillant heat pumps from 2018 with EEBUS can be controlled through the ONE Controller, and the SolarEdge Home Hot Water Controller feeds surplus into an immersion heater.

Nibe: NIBE’s own PV solution is the EME 20 communication module for S-series units (S1155, S1255, SMO S40, VVM S320/S325). It reads the inverter over RS485 Modbus RTU (SunSpec) and, under menu 4.2.2 “Solar electricity”, lets the heat pump raise room, hot-water or pool temperature when there is surplus; with an extra energy meter household consumption can be prioritised.

Zerofy connects the two: it reads SolarEdge production and controls your Nibe heat pump to match, together with your other devices in one app, with dynamic tariffs and forecast-based Smart mode.

Setting up SolarEdge and Nibe in Zerofy

1. Connect SolarEdge

Zerofy connects to SolarEdge’s monitoring cloud with the same login you use for the SolarEdge Monitoring website or the mySolarEdge app.

1. Make sure your SolarEdge inverter is online and your account has the Owner role on the site.
2. Add a new SolarEdge device in Zerofy.
3. Log in with your SolarEdge Monitoring / mySolarEdge credentials and follow the on-screen prompts.

Good to know: Your account needs the Owner role, which the installer usually assigns to the system owner during setup; ask your installer if you don’t have it. Battery and meter data depend on how your system is configured.

Step-by-step guide for SolarEdge

2. Connect Nibe

Zerofy connects to the myUplink cloud API with your myUplink login (OAuth) and shows the heat pump as a Space Heating and a Hot Water Tank device; Autopilot controls the hot-water boost.

1. Register the heat pump in myUplink and make sure it is online.
2. Activate a myUplink Premium subscription for the system.
3. In Zerofy, add Nibe and log in with your myUplink credentials.
4. Enable Autopilot (Solar or Smart mode) for the Hot Water Tank.

Good to know: Without a myUplink Premium subscription the API access does not work. Zerofy currently steers only the hot-water boost; flow-temperature control is not available yet.

Step-by-step guide for Nibe

3. Turn on Autopilot

In Zerofy, open your Nibe heat pump, turn on Autopilot and choose Solar – or Smart to also use dynamic tariffs and forecasts. Set the priority, activation threshold and minimum runtime.

Dynamic tariffs

Zerofy can also run your Nibe heat pump on dynamic electricity prices (EPEX Spot or Nord Pool, e.g. Tibber or aWATTar) or on a fixed time-of-use tariff. Smart mode combines those prices with forecasts of your household consumption and your SolarEdge solar production.

Learn more about Smart Mode

About SolarEdge and Nibe

SolarEdge – Israeli company (Herzliya) known for inverters with a power optimizer on every module. Homes typically have a SolarEdge Home Wave single-phase or Home Hub three-phase inverter with optimizers, often with a SolarEdge Home Battery and SolarEdge Home smart-energy accessories. Monitoring app: SolarEdge Monitoring / mySolarEdge app.

Nibe – NIBE is a Swedish heat pump maker (Markaryd). Homeowners typically have a ground-source S1155/S1255, an air-to-water heat pump with an SMO or VVM indoor unit, or an exhaust-air F730/F750, all connected to the myUplink cloud. Products: S1155, S1255, S2125 with SMO S40 / VVM S320, F-series (F1155, F1255, F2120, F730, F750).

Manufacturer information last checked: October 2026.

All devices that work with SolarEdge