Enphase + Huawei SCharger

What Zerofy can do with Enphase and Huawei SCharger

In practice

• Zerofy adjusts the charging current of your Huawei SCharger but doesn’t switch phases. On a three-phase connection, solar charging needs at least about 4.1 kW of surplus (6 A × 3 × 230 V); on a single-phase connection about 1.4 kW.
• A typical Enphase home system (3–10 kW) needs a sunny midday to reach the 4.1 kW three-phase minimum. Wired single-phase, the charger starts from about 1.4 kW but charges at no more than about 3.7 kW.
• Zerofy gets new Enphase data every 5 minutes and adjusts accordingly. A minimum runtime and an activation threshold in Autopilot keep passing clouds from interrupting charging.
• Zerofy also shows your Enphase battery, so you can see whether surplus goes into the battery or into the car.
• If your car is connected to Zerofy too, turn on Autopilot for either the car or the charger, not both.
• In Huawei’s own mode, the 22KT charges three-phase from about 4.14 kW and drops to single-phase below that if “Switch Between Single and Three Phases” is on; it then charges on L1 only, so Huawei advises wiring L1 to the least-loaded phase. Via OCPP, Zerofy sets the power but not the phases, so the minimum is 6 A: about 1.4 kW single-phase or 4.1 kW three-phase.

What Enphase and Huawei SCharger offer on their own

Enphase: Enphase sells its own IQ EV Charger 2, shipping in 14 European markets since March 2025, with a Green Charging mode that uses only surplus solar and automatic 1-/3-phase switching, so charging can start from about 1.38 kW. Third-party chargers can be controlled via OCPP 1.6J through the IQ Energy Router (up to two chargers), but only models on Enphase’s supported list.

Huawei SCharger: Huawei’s own surplus mode is “PV Power Preferred” in FusionSolar. It needs a Huawei SUN2000 inverter and a Huawei Smart Power Sensor at the grid connection (DTSU666-FE directly, or an RS485 meter such as DTSU666-H relayed by the WLAN/FE Smart Dongle) and does not work in charger-only setups.

Zerofy connects the two: it reads Enphase production and controls your Huawei SCharger to match, together with your other devices in one app, with dynamic tariffs and forecast-based Smart mode.

Setting up Enphase and Huawei SCharger in Zerofy

1. Connect Enphase

Zerofy connects to your system through the Enphase cloud: you log in with your Enphase Enlighten credentials and Zerofy reads PV production, meter (consumption) and battery data.

1. Make sure your system is online and you have an account on Enphase Enlighten.
2. In Zerofy, add an inverter, choose Enphase and log in with your Enlighten credentials.
3. Configure the meters: the grid meter as main meter (bi-directional or consumption), production as a sub meter of type production.

Step-by-step guide for Enphase

2. Connect Huawei SCharger

The SCharger connects to Zerofy via OCPP, which is set in installer mode of the Huawei Fusion app; Zerofy can then start, stop and set the charging power.

1. Update the charger to FusionCharge V100R023C10SPC220 or later (OTA via the app).
2. In Zerofy, add a Huawei SCharger and copy the OCPP link (ocppconnect.net/<id>).
3. In the Fusion app, connect to the charger’s Wi-Fi, log in with Installer Mode and open OCPP.
4. Choose “Insecure transmission with basic authentication” and enter domain ocppconnect.net, port 80, path and username <id>, and any password.

Good to know: OCPP can only be set in installer mode, so many owners need their installer for the one-time setup. Older firmware must be updated first.

Step-by-step guide for Huawei SCharger

3. Turn on Autopilot

In Zerofy, open your Huawei SCharger, turn on Autopilot and choose Solar – or Smart to also use dynamic tariffs and forecasts. Set the priority, activation threshold and minimum runtime.

Dynamic tariffs

Zerofy can also run your Huawei SCharger on dynamic electricity prices (EPEX Spot or Nord Pool, e.g. Tibber or aWATTar) or on a fixed time-of-use tariff. Smart mode combines those prices with forecasts of your household consumption and your Enphase solar production.

Learn more about Smart Mode

About Enphase and Huawei SCharger

Enphase – Enphase Energy (Fremont, California) makes microinverters: each panel gets its own IQ8 unit of about 300–330 VA, connected through an IQ Gateway. The AC-coupled IQ Battery 5P adds storage in 5 kWh steps, and everything is monitored in the Enphase App (Enlighten). Monitoring app: Enphase App / Enlighten.

Huawei SCharger – The SCharger is the wallbox of the Chinese inverter maker Huawei (7.4 kW single-phase or 22 kW three-phase), the natural choice for homes with a Huawei inverter. It is sold through solar installers and is set up and monitored in FusionSolar. Products: SCharger-7KS-S0, SCharger-22KT-S0.

Manufacturer information last checked: October 2026.

All devices that work with Enphase