SolarEdge + OCPP chargers

What Zerofy can do with SolarEdge and OCPP chargers

In practice

• Zerofy adjusts the charging current of your OCPP charger but doesn’t switch phases. On a three-phase connection, solar charging needs at least about 4.1 kW of surplus (6 A × 3 × 230 V); on a single-phase connection about 1.4 kW.
• A typical SolarEdge home system (3–10 kW) needs a sunny midday to reach the 4.1 kW three-phase minimum. Wired single-phase, the charger starts from about 1.4 kW but charges at no more than about 3.7 kW.
• Zerofy gets new SolarEdge data every 5 minutes and adjusts accordingly. A minimum runtime and an activation threshold in Autopilot keep passing clouds from interrupting charging.
• Zerofy also shows your SolarEdge battery, so you can see whether surplus goes into the battery or into the car.
• If your car is connected to Zerofy too, turn on Autopilot for either the car or the charger, not both.
• Many chargers switch off their own app or solar mode while an external OCPP backend is active (for example enercab, Growatt THOR, SolaX in its OCPP scene), so Zerofy takes over. Zerofy sets the power over OCPP but not the phases, so a three-phase charger needs about 4.1 kW of surplus (3×6 A) unless it switches phases by itself.

What SolarEdge and OCPP chargers offer on their own

SolarEdge: SolarEdge sells its own EV charger, controlled from the mySolarEdge app. With the SolarEdge ONE Controller (inverter firmware 4.22 or later), mySolarEdge can instead run one third-party OCPP 1.6J charger with Excess Solar charging: MENNEKES AMTRON, Wallbox Pulsar Max/Plus/Pro, Alfen Eve S-line/Pro-line or ABB Terra AC. Only one charger can be used at a time.

OCPP chargers: OCPP itself has no solar mode: since 1.6 it carries smart-charging profiles, so the backend sets the current limit and decides when to charge. Solar behaviour therefore comes from whichever system is the backend, or from the charger’s own meter-based mode.

Zerofy connects the two: it reads SolarEdge production and controls your OCPP charger to match, together with your other devices in one app, with dynamic tariffs and forecast-based Smart mode.

Setting up SolarEdge and OCPP chargers in Zerofy

1. Connect SolarEdge

Zerofy connects to SolarEdge’s monitoring cloud with the same login you use for the SolarEdge Monitoring website or the mySolarEdge app.

1. Make sure your SolarEdge inverter is online and your account has the Owner role on the site.
2. Add a new SolarEdge device in Zerofy.
3. Log in with your SolarEdge Monitoring / mySolarEdge credentials and follow the on-screen prompts.

Good to know: Your account needs the Owner role, which the installer usually assigns to the system owner during setup; ask your installer if you don’t have it. Battery and meter data depend on how your system is configured.

Step-by-step guide for SolarEdge

2. Connect OCPP chargers

You enter Zerofy’s OCPP URL in your charger’s OCPP settings; Zerofy then acts as the backend and can start, stop and set the charging power.

1. Check that your charger supports OCPP 1.6 and lets you change the backend address.
2. In Zerofy, add an OCPP charger and copy the OCPP URL.
3. Paste it into the OCPP settings of your charger’s app or web page and wait for it to connect.

Good to know: Not every OCPP charger lets the owner choose the backend: some need the installer’s service tool (Alfen, ABB), some pick from a preset list (Peblar) or whitelist the address first (Smappee), and some offer no owner OCPP at all (Tesla Wall Connector, Ohme).

Step-by-step guide for OCPP chargers

3. Turn on Autopilot

In Zerofy, open your OCPP charger, turn on Autopilot and choose Solar – or Smart to also use dynamic tariffs and forecasts. Set the priority, activation threshold and minimum runtime.

Dynamic tariffs

Zerofy can also run your OCPP charger on dynamic electricity prices (EPEX Spot or Nord Pool, e.g. Tibber or aWATTar) or on a fixed time-of-use tariff. Smart mode combines those prices with forecasts of your household consumption and your SolarEdge solar production.

Learn more about Smart Mode

About SolarEdge and OCPP chargers

SolarEdge – Israeli company (Herzliya) known for inverters with a power optimizer on every module. Homes typically have a SolarEdge Home Wave single-phase or Home Hub three-phase inverter with optimizers, often with a SolarEdge Home Battery and SolarEdge Home smart-energy accessories. Monitoring app: SolarEdge Monitoring / mySolarEdge app.

OCPP chargers – OCPP (Open Charge Point Protocol) is the open standard from the Open Charge Alliance for communication between a charger and a management system; version 1.6 from 2015 is the most widely used, in its JSON variant 1.6J. A charger can only be connected to one OCPP backend at a time. Products: Any charger with OCPP 1.6J and a freely configurable backend, e.g. Alfen Eve, KEBA KeContact P40, Charge Amps Halo, Autel MaxiCharger, enercab smart.

Manufacturer information last checked: October 2026.

All devices that work with SolarEdge