Fronius + CTA

What Zerofy can do with Fronius and CTA

In practice

• When there’s enough surplus, Zerofy switches the relay and the heat pump receives the SG Ready signal. How it reacts – for example by heating the hot-water tank to a higher temperature – is set in the heat pump’s own controller.
• A heat pump draws roughly 1–3 kW while running, which a typical Fronius home system (3–10 kW) can cover on sunny days.
• Zerofy gets new Fronius data every 5 minutes. Heat pumps shouldn’t switch often, so set a minimum runtime in Autopilot.
• Zerofy also shows your Fronius battery, so you can see whether surplus goes into the battery or into the heat pump.
• CTA’s own tip for SG Ready operation: if rooms get too warm or too cold, change the upper temperature limit by 1 °C at a time and leave it for one to two days before adjusting again; agree the values with your heating installer.

What Fronius and CTA offer on their own

Fronius: The Fronius Ohmpilot feeds surplus into a heating rod (0.3–3 kW single-phase, 0.9–9 kW three-phase) and has a control output for a heat pump with an SG Ready input. GEN24 inverters can also switch an SG Ready input through one of their four digital outputs plus a coupling relay, and Fronius lists direct integrations with heat pumps from IDM, Bosch and NIBE.

CTA: For PV self-consumption, CTA connects its heat pumps to external energy management systems via a PV input, SG Ready or Modbus (Optiheat and Aeroheat). CTA publishes SG Ready instructions per model and a compatibility list for the Swiss Solar Manager gateway (Modbus TCP/RTU).

Zerofy connects the two: it reads Fronius production and controls your CTA heat pump to match, together with your other devices in one app, with dynamic tariffs and forecast-based Smart mode.

Setting up Fronius and CTA in Zerofy

1. Connect Fronius

Zerofy reads your system from Fronius Solar.web through a guest account that you create for Zerofy.

1. Make sure your Fronius inverter is online and shows up in Solar.web.
2. In Solar.web, go to Settings → Permissions and create a new guest account.
3. Add Fronius in Zerofy and log in with the guest account credentials.

Step-by-step guide for Fronius

2. Connect CTA

The Zerofy docs have no CTA-specific guide; the documented way to control a CTA heat pump is Zerofy’s SG Ready integration, with a smart relay such as a Shelly wired to the heat pump’s SG Ready inputs.

1. Check in CTA’s SG Ready compatibility list that your model and controller (Optiplus, Optiplus 3, Aeroplus 2.0/2.1) are listed.
2. Have an electrician wire a smart relay (e.g. Shelly) to the heat pump’s SG Ready inputs.
3. Add the relay to Zerofy and configure it as SG Ready controller.

Good to know: CTA marks Optiheat Inverta units and several Aeroheat models as needing a software or controller update for SG Ready. For older or unlisted units, CTA says integration can mean extra cost, e.g. a controller replacement.

Step-by-step guide for CTA

3. Turn on Autopilot

In Zerofy, open your CTA heat pump, turn on Autopilot and choose Solar – or Smart to also use dynamic tariffs and forecasts. Set the priority, activation threshold and minimum runtime.

Dynamic tariffs

Zerofy can also run your CTA heat pump on dynamic electricity prices (EPEX Spot or Nord Pool, e.g. Tibber or aWATTar) or on a fixed time-of-use tariff. Smart mode combines those prices with forecasts of your household consumption and your Fronius solar production.

Learn more about Smart Mode

About Fronius and CTA

Fronius – Austrian manufacturer of inverters, welding and battery-charging technology. Homeowners typically have a Primo GEN24 (single-phase, 3–6 kW) or Symo GEN24 (three-phase, 3–10 kW) hybrid inverter, older Primo/Symo SnapINverters, and the Fronius Reserva battery (6.3–15.8 kWh). Monitoring app: Fronius Solar.web.

CTA – CTA AG is a Swiss manufacturer of heat pumps and cooling machines, with production at its headquarters in Münsingen near Bern. Its home range covers Optiheat ground-source and water-source heat pumps and Aeroheat air-source heat pumps. Products: Optiheat (brine/water and water/water), Optiheat Inverta, Aeroheat (air/water, indoor and outdoor units), Aeroheat Inverta.

Manufacturer information last checked: October 2026.

All devices that work with Fronius