Enphase + CTC

What Zerofy can do with Enphase and CTC

In practice

• Hot water is the simplest heat store: Autopilot can use the hot-water boost of your CTC heat pump to heat water in hours with surplus.
• A heat pump draws roughly 1–3 kW while running, which a typical Enphase home system (3–10 kW) can cover on sunny days.
• Zerofy gets new Enphase data every 5 minutes. Heat pumps shouldn’t switch often, so set a minimum runtime in Autopilot.
• Zerofy also shows your Enphase battery, so you can see whether surplus goes into the battery or into the heat pump.
• If you use CTC’s own spot-price control in myUplink, its “Blocking” at high prices can lower the hot-water setpoint; check that the CTC price limits and Zerofy’s Smart mode don’t pull in opposite directions.

What Enphase and CTC offer on their own

Enphase: The IQ Energy Router+ (IQ Energy Router plus Energy Meter and SG Ready Relay) controls one SG Ready heat pump. It only uses SG Ready states 2 (normal) and 3 (recommended on), and Enphase publishes wiring guides for Daikin Altherma 3, Vaillant aroTherm plus and iDM.

CTC: CTC controllers have SmartGrid inputs (terminals K22–K25, a SmartControl wireless accessory or BMS): when an inverter or energy manager closes both contacts (“SmartGrid Overcapacity”), the controller raises the room/flow setpoint by 1–5 °C and the hot-water setpoint by up to 30 °C. Through myUplink, CTC can also download spot prices and switch between “Low price” and “Blocking” on its own.

Zerofy connects the two: it reads Enphase production and controls your CTC heat pump to match, together with your other devices in one app, with dynamic tariffs and forecast-based Smart mode.

Setting up Enphase and CTC in Zerofy

1. Connect Enphase

Zerofy connects to your system through the Enphase cloud: you log in with your Enphase Enlighten credentials and Zerofy reads PV production, meter (consumption) and battery data.

1. Make sure your system is online and you have an account on Enphase Enlighten.
2. In Zerofy, add an inverter, choose Enphase and log in with your Enlighten credentials.
3. Configure the meters: the grid meter as main meter (bi-directional or consumption), production as a sub meter of type production.

Step-by-step guide for Enphase

2. Connect CTC

Zerofy reaches CTC heat pumps through the myUplink cloud, the same connector used for NIBE, with your myUplink login; Autopilot controls the hot-water boost.

1. Connect the heat pump to the internet and register it in the myUplink app.
2. Make sure your myUplink account has the subscription needed for remote control.
3. In Zerofy, connect myUplink and log in with your myUplink credentials.
4. Enable Autopilot (Solar or Smart mode) for the hot-water tank.

Good to know: Zerofy steers only the hot-water boost on CTC units, not room or flow temperature.

3. Turn on Autopilot

In Zerofy, open your CTC heat pump, turn on Autopilot and choose Solar – or Smart to also use dynamic tariffs and forecasts. Set the priority, activation threshold and minimum runtime.

Dynamic tariffs

Zerofy can also run your CTC heat pump on dynamic electricity prices (EPEX Spot or Nord Pool, e.g. Tibber or aWATTar) or on a fixed time-of-use tariff. Smart mode combines those prices with forecasts of your household consumption and your Enphase solar production.

Learn more about Smart Mode

About Enphase and CTC

Enphase – Enphase Energy (Fremont, California) makes microinverters: each panel gets its own IQ8 unit of about 300–330 VA, connected through an IQ Gateway. The AC-coupled IQ Battery 5P adds storage in 5 kWh steps, and everything is monitored in the Enphase App (Enlighten). Monitoring app: Enphase App / Enlighten.

CTC – CTC is a Swedish heat pump maker from Ljungby. Its air-to-water, ground-source and exhaust-air heat pumps and EcoZenith indoor modules are controlled remotely through the myUplink app. Products: CTC EcoAir, CTC GS/GSi 600, CTC EcoZenith i255/i360/i555 Pro, CTC EcoPart i600M, CTC EcoVent i360F, CTC EcoLogic L/M.

Manufacturer information last checked: October 2026.

All devices that work with Enphase